personalized gifts for her How to Install Faux Wood Beams- Beam Me Up Scottie! pillow covers farmhouse
Updated: :2020-01-19

Beams. I dig 'em. Heather from The Heathered Nest here, and Ithink I'vealways had a thing for beams and today, I am going to show you how to install faux wood beams yourself.

To me, beams say “;come on in and snuggle by the fire”;…;

accent pillow case baby canvas outdoor

and “;prop your feet up and relax in our rustic retreat”;.

They also say “;You the type of homeowner that likes paying for things through the nose? Then buy a couple of us!”; That's when I stopped liking beams. Drats. Design dream dashed.

Or so Ithought.

Until Idiscovered…;.FAUX BEAMS! For just a fraction (like 1/5) of the cost of REAL wood beams, and just a teensy, tiny percentage of the weight (which is important for installation), it is possible to buy and install faux wood beams. And guess what? They look real. Seriously. Hallelujah, hap-beam days are here again!! This post contains some affiliate links. Click here to read my full disclosure policy.

Do you guys want to know how to work with them? The male half of the Heathered Nest is gonna walk you through the process…;

DON'T GET SCARED…;this seems like a lot of stuff, but seriously, you can do this!

1. First step is to decide wherepersonalized gifts for her, and how many faux wood beams you want. Sounds easy and obvious. But there's so many options for how to use these beams, that for us at least, this was the most difficult part of the entire process. We settled on usingtwo beams based on the size of our room and the location of ourchandelier, which we wanted to remain a focal point. Also remember that the size of the beams is important…the higher the ceiling, the bigger the beam you probably want.

Here's an image of our family room from the real estate listing before we bought ourhouse. We decided to put two beams in here to add somerustic flare and architectural detail since the room had nice high cathedral ceilings, but nothing to accent them.

2.Installing joist hangers is the first step in the actual installation. Joist hangers you say? Aren’t those for, like, hanging joists? Yes they are, but they also come in handy forinstalling these faux wood beams. Since ours are installed in a vaulted space, we used joist hangers that were adjustable to the angle of our ceiling. If you are lucky, you have a stud where you want to put the hangers, which makes them pretty easy to install. If not, you need to use anchors..not a big deal in this situation since the faux beams are so light. They're made of high density foam…;picture below.

The key here is to get all four joist hangers (two perbeam) at the same height and level, which will greatly help when you put up the beam. A laser level comes in handy here, or a string with a line level will work too.

3.Withthe joist hangers up, now we'llinstall 2×;4’s in the joist hangers. You need to sister two 2×;4’s together (meaning, two 2×;4’s screwed together, lengthwise). Remember, they make 2×;4’s up to 16’ in length, so get the longest 2×;4 you need fit the entire span. This makes for an overall stronger beam…you don’t want to try to put two 8’ 2×;4’s together to make a 16’ span. Once you have sistered your 2×;4’s together, cut them to length. Since this is a cathedral ceiling, you will need to cut an angle on the ends of the 2×;4's. To measure this angle you can use an angle finder (I know, great name for a tool). Once they are cut tolength you need simply set them in the joist hangers and screw them together….you are now about 75% done with this project!

BAD PICTURE ALERT…;but you can kind of see the “;sistered”; 2×;4's in this image if you look closely. You can also see the ends of the 2×;4's sitting in the joist hangers. Also, those red telescoping poles on either end of the 2×;4's? Those were pretty clutch for completing this project.

4.Time to cut the faux beams to length. This was the mostpainful part of the processbecausewe had to cut the ends of our beams at an angle. Getting the angle just right was a little tricky. Use your trusty angle finder to measure the angle of the ceiling (remember, measure twice, cut once). The actual cutting of the beams is no problem! You could almost use a butter knife (just kidding, use a hand saw silly). It took a little bit of trial and error to get the angle right, but we finally got it pretty close.

5.Moment of truth time. Install your beam. Believe or not, this is the easiest part. You'll need your helper/second set of hands. The beam is open on the top (shaped like a “U”). Here's a picture of it, uninstalled.

Lift the beam up to cover the 2×;4 “joist” you installed. Depending on the width of your beam, it might be a snug fit around your 2×;4(s). If not, cut a few 2×;4 spacers out of whatever scrap wood you have lying around, and screw the scrap spacers to the joist. Use the spacersevery few feet or so. Now lift the beam back up and see if you have a snug fit. If not repeat this process with various size spacers. Once the beam fits up there nicely, put a level on it and get it nice and straight.

Even if your joists are a little off, you can still make the beam perfectly level. Now screw through the faux beam into the joist. We used black drywall screws. Fill the screw holes with wood putty (make sure the putty matches the beam) and there you have it…beautiful faux wood beams!

And no one will be able to tell the difference.

So come on! Faux-get about it! Give these beams a try. We “;wood”; love to see how they turn out if you do!

It's been awesome to meet you guys over here at Designer Trapped in a Lawyer's Body. Don't be a stranger! I would love to connect with you on social media–;you can find me pretty much everywhere: Facebook | Pinterest | Google | Twitter | Instagram

Now, be sure to stop by my blog, The Heathered Nest, and check out some of my most popular posts. Just click on any of the images below to be taken to the full posts!

Guest Room Reveal

Guest Bath Reveal

Dining Room Reveal

I am ALL about?using products that are non-toxic. Especially when it comes to Toxin Free?Cleaning and my home. I was thrilled to partner with my local Safeway and try the new Open Nature? Household Cleaning and Care products which are safe for my home and family.

It's definitely a statement.

Paper templates are invaluable for determining and marking fabric for embroidery designs. There are several ways you can get a paper template.

Previous: personalized gifts for her DIY Paper Mache Letters With a Twist pillow covers farmhouse
Next: personalized gifts for her How to Install Quarter-Round Molding pillow covers farmhouse

custom gift for pets    |     customized gifts for mom    |     personalized gifts for her    |    

Powered by custom gift for pets @2018 RSS Sitemap html Sitemap

Copyright 站群系统 © 2013-2019 Personalize